Skip to content
VisionGreen

Building management systems and BMS optimisation

A building management system controls the heating, cooling, ventilation and often the lighting in a building from one place. It is one of the best energy tools a building can have, and one of the most commonly misused.

By Rachel McKeogh, Operations Support Manager at VisionGreen. Updated .

What a BMS does

A BMS system switches plant on and off to schedules, holds temperatures to setpoints, and responds to sensors such as occupancy or outside temperature. In a hotel, office, school or factory it typically runs boilers, heat pumps, chillers, air handling units and fans.

The energy it saves depends entirely on how it is set up. A BMS running last year's schedules, or with plant left in manual after a service visit, can waste as much as it saves.

BMS optimisation: where the savings are

Most of the savings from a building management system come from optimisation, not new hardware. In our experience the same handful of faults turn up in building after building, which is why the checklist below is short.

The 12-point BMS optimisation checklist

Work through these with the BMS front end open and a week of energy data beside it.

  • Schedules match the hours the building is actually used, including weekends, bank holidays and seasonal closures
  • Optimum start is enabled, so plant starts as late as the weather allows rather than at a fixed time
  • Night and weekend setback is set on heating and ventilation, not just on the front-of-house zones
  • Heating and cooling setpoints have a dead band between them, so the two never run against each other
  • No plant is left in manual or hand mode after a service visit or a complaint
  • Air handling units run to CO2 or occupancy where they can, instead of full speed all day
  • Frost protection is set sensibly, not at a level that quietly heats the building all night
  • Sensors are in the right place and calibrated, so the BMS sees the building correctly
  • Pump and fan speeds are controlled on demand, not fixed at maximum
  • Hot water generation and recirculation follow a schedule, not a 24-hour loop
  • Alarms go to someone who reads them, and overrides time out instead of staying on
  • Someone checks the energy data against the schedules every month, so the settings do not drift back

A worked example: what a mis-set BMS costs

Illustrative figures. An office building of 4,000 square metres has a BMS running two air handling units, a gas boiler and a chiller. The schedules were set when the building opened and never revisited. The plant starts at 5am for a 8am opening, the setback was switched off after a cold-morning complaint, and the ventilation runs at full speed from 5am to 8pm.

Monitoring shows the building drawing 85 kW from 5am, three hours before anyone arrives. Three hours a day over 250 working days is 750 hours; at 85 kW that is about 64,000 kWh, roughly €15,000 a year at 2026 business rates, spent on an empty building. Restoring optimum start and setback and putting the ventilation on occupancy control takes a controls engineer a day. The gas side shows the same pattern on the boiler.

SEAI pays a fixed €2,000 towards exactly this kind of work under the Business Energy Upgrade Scheme, which in this example covers most of the day's work and the metering that found it.

BMS and energy monitoring

A BMS controls equipment. Energy monitoring measures what the equipment actually uses. Put together, monitoring shows when the BMS is not doing what it should: plant starting hours early, heating on at weekends, chillers running in winter. Many buildings with a BMS still waste energy because nobody checks the data.

A BMS also only sees the plant it is wired to. Kitchen equipment, refrigeration, process machinery and most lighting are usually outside it. Circuit-level monitoring covers the whole board, which is why we fit it before we touch the BMS.

SEAI grants for building management systems

The SEAI Business Energy Upgrade Scheme funds a new BMS or an upgrade, at up to 30% of the cost to a maximum of €30,000, and pays a fixed €2,000 towards optimising an existing BMS. Approval must be in place before any work starts. Larger controls projects can be part of an EXEED application.

Do you need one?

If your building has central heating, cooling or ventilation plant and no central control, a BMS usually pays back. If you already have one, the first step is almost always optimisation, checked with monitoring, before any new hardware.

Related guides

Where VisionGreen can help

Common questions

What is a building management system and do I need one?

A building management system (BMS) is a control system that runs a building's heating, cooling, ventilation and often lighting from one place, on schedules and setpoints. Most businesses with central plant benefit from one; if you already have a BMS, optimising it is usually the cheaper first step.

What is BMS optimisation?

Adjusting an existing BMS so its schedules, setpoints and controls match how the building is used today: optimum start, night setback, dead bands, plant returned to automatic, ventilation on demand, sensors calibrated. It typically costs far less than new hardware, and SEAI pays €2,000 towards it under the Business Energy Upgrade Scheme.

How much energy can BMS optimisation save?

It depends on how far the settings have drifted. As an illustration, plant starting three hours before a building opens can cost 60,000 kWh a year on its own. The common faults are schedules, setback switched off, plant left in manual and ventilation at full speed, and a day of controls work usually fixes most of them.

Are there grants for building management systems in Ireland?

Yes. The SEAI Business Energy Upgrade Scheme funds a BMS install or upgrade at up to 30%, to a maximum of €30,000, and pays €2,000 towards optimising an existing BMS. Approval must come before the work.

Who installs building management systems in Ireland?

VisionGreen specifies, upgrades and optimises building management systems as part of wider energy projects, sets the schedules and setpoints from monitoring data, and checks afterwards that the savings hold.

Energy monitoring vs a building management system: which do I need?

Usually both. The BMS controls the plant; monitoring measures what it uses and shows when the BMS is set up wrongly. Monitoring is often the cheaper place to start, because it shows what the BMS needs to change, and it covers the kitchen, refrigeration and lighting loads a BMS does not see.

Want this applied to your building?

Start with an energy audit. If you spend over ten thousand euro a year on energy, the SEAI grant covers most of the cost.

Call usEnquire